CGI Door Installation Nationwide | Winslow Windows & Doors

CGI Door Installation: The Miami Owner’s Guide

CGI door installation in Miami typically runs $1,100 to $2,600 installed, depending on the model line, panel configuration, and whether we’re replacing a single door slab or rebuilding the frame assembly. Most CGI parts swaps happen same day once we confirm the exact series, because we stock common CGI hinge kits, rollers, tracks, handlesets, and weatherstripping on the truck. The call usually starts the same way: a homeowner tells us the door drags, sticks, rattles in the wind, or won’t seal tight against the afternoon storms rolling in off Biscayne Bay. Nine times out of ten, it’s a failed part, not a failed door, and the fix costs far less than a full replacement.

Call (863) 862-5435

Key Takeaways:

• CGI parts are series-specific. The part number matters more than the door size.
• Most failed components (rollers, hinges, handlesets, weatherstripping) are replaceable without swapping the entire door.
• Parts and labor get a written line-item quote before we start, so the number on the invoice matches the number on the estimate.
• We’re an independent installer. We’re not owned by or affiliated with CGI, but we’ve installed and serviced their door lines for over a decade across Miami-Dade.

Which CGI Models This Applies To

CGI manufactures impact-rated door systems across several series, and the model line dictates which replacement parts fit. The most common line we service in Miami is the Estate Collection (often paired with CGI’s Sentinel and Tribute impact doors), but we also handle parts for their sliding glass and French door configurations that show up in older Coral Gables and Pinecrest homes. The important thing to know: a hinge kit from one CGI series will not always interchange with another, even if the door slabs look identical. We match parts by the model number on the frame label, usually a small CGI placard on the hinge-side jamb, and by the door’s glass thickness and panel profile. In some cases, a quality aftermarket equivalent is available and frankly is the smarter buy. In others, like the interlocking astragal on a French pair or the multi-point lock hardware, OEM is the only route that holds up against Miami’s humidity and wind cycles. We’ll tell you which is which before you spend a dollar.

Signs Your CGI Door Installation Is Failing

• The door scrapes or drags across the threshold. This is usually a worn roller or hinge bushing, not a structural issue. Left alone, the drag will start chewing through the threshold and the door sweep, and eventually the panel itself.
• You can see daylight around the edges when the door is closed. Weatherstripping compresses over time, and in Miami the combination of salt air and UV eats rubber seals faster than anywhere else in the state. A gap means water intrusion during summer downpours, and that water rots the jamb from the inside.
• The multi-point lock binds or won’t engage fully. CGI doors use long throw bolts at the top and bottom of the panel. When grime, sand, or corrosion builds up in the track, the bolts hang up. Forcing the handle bends internal levers, and then the whole lock assembly has to come out.
• The door slams shut with a metal-on-metal sound. That’s the door closer or the hinge side bracket failing. On a heavy impact-rated slab, this is a part that needs replacing sooner rather than later. A falling CGI door panel can weigh enough to hurt someone.
• You hear a rattle or clunk during wind gusts. Loose or worn rollers let the panel shift inside the track, and that movement stresses the glass and frame. If the panel moves more than a quarter inch in the track, the part has failed and needs replacement before the next storm season.

Replacement Cost & What’s Included

In Miami, most single-panel CGI door part replacements run between $180 and $640 installed, with the part itself typically accounting for 40 to 60 percent of the total. Full door slab replacements or complete hardware overhauls can push into the $1,100 to $2,600 range I mentioned up top. What drives the spread: the specific series, whether the part is OEM or aftermarket, and how much of the surrounding track or frame needs attention. Every job gets a written line-item quote before we start. Not a ballpark. Not a handshake number. The part, the labor, and the disposal are on the page, and the invoice matches it. Ed Winslow’s name is on the door. Literally. So the quote stands and the work carries our 36500-Day Done Right Promise. If something isn’t right, we come back and make it right.

DIY or Call Us?

Some things an owner can safely handle: tightening visible hinge screws, clearing debris from the bottom track, and spraying a dry lubricant on rollers and lock points. Those are maintenance tasks, not repairs. What an owner shouldn’t touch: anything involving the multi-point lock’s internal linkage, the spring-loaded rollers on a heavy impact door, or any adjustment that requires lifting or unweighting the door slab. A CGI impact door panel weighs anywhere from 180 to 400 pounds depending on size. Without the right lift plates and a second set of hands, that’s a crushed foot or a broken window waiting to happen. This is the part where we say plainly: call a professional. Specifically, call us at (863) 862-5435. We’ll get the right part matched to your series, and the job gets done the same day in most cases.

FAQs